Spokane Valley · gas and electric dryers
Dryer repair in Spokane Valley for crawlspace runs and roof vents
Towels damp after an hour, a squeal from the first minute, a drum that hums and never moves. We fix gas and electric dryers from Opportunity to Greenacres and write one repair number with the $99 diagnostic inside it.
- No surcharge
- Same price card at any Valley address, no distance fee
- Heat metered
- Element, fuses or igniter tested before anything is condemned
- Online saving
- Up to $22 off a repair booked through the site
In Spokane Valley the vent usually gives the game away before the dryer does. Most of the no-heat calls we take here end the same way: an electric element with a broken coil, and behind it an exhaust run that was already half closed. Put in a new element and leave the run alone, and the next thermal fuse goes by spring. That is why every Valley dryer visit covers the vent, from the drum outlet to the hood outside, with airflow and exhaust temperature measured rather than guessed. Where we find a section of foil flex sagging between crawlspace joists, we recommend smooth metal duct in its place, since the ridges of foil hold lint and the sags collect it.
The order of testing matters. An electric dryer gets a resistance reading on the element and a continuity check on the thermal fuse and cycling thermostat. On a gas dryer we watch the igniter glow and listen for the valve coils to open, because coils that open once and then quit produce the classic half-heat complaint: warm for ten minutes, cool after that. Next comes the drive path, belt tension, idler pulley, rollers, and the rear bearing on drum-supported models. The control board is last, and it has to fail on a meter before it ever appears on a quote. The whole sequence is covered by the $99 diagnostic.
Valley dryer faults, cause by cause
| What you notice | What it usually is | What we do |
|---|---|---|
| Hour-long cycle, towels cold | Element coil broken after months behind a restricted vent | New element, crawlspace or roof run cleared, exhaust reading taken |
| Warm at first, then cool | Gas valve coils that open once and quit | Coil set replaced, ignition watched through a full heat cycle |
| Two cycles for one load | Crushed or lint-packed duct, or softener film on the sensor bars | Duct cleared or replaced on site, sensor cleaned |
| Breaker trips as the heat starts | Shorted element or a worn 30-amp receptacle | Both tested by one technician; the actual fault repaired |
| Hum, no tumble | Snapped belt or seized idler pulley | Belt and idler replaced together in one stop |
| Squeal turning to a grind you feel in the floor | Drum bearings or rollers worn through | Drum pulled, bearings and rollers replaced |
How Valley houses route their dryer air
The single-story ranches south of Sprague, on Chester and Ponderosa and through the blocks between University and Pines, were laid out with the laundry near the middle of the house. Exhaust from those dryers travels twenty feet or more through the crawlspace before it sees daylight, and lint settles along every foot of it. Valley winters are dry enough to press that lint into felt, so a duct that moves air easily in June can be nearly shut by February. The older ranches in Opportunity follow the same pattern, often with a dryer that has turned on one belt for a long time. A crawlspace run also hides its faults: a joint that has pulled apart can dump lint and damp air under the house for years before anyone looks, so we check every joint we can reach.
East of Sullivan and out toward Barker Road, the newer two-story homes send the exhaust the opposite way, up through the framing to a roof cap. Those runs fail at the top. The cap damper sticks in January or the screen fills, and a dryer that seemed fine at Thanksgiving needs two cycles by New Year. Many dryers in the Greenacres and Veradale subdivisions burn natural gas, so each of those visits ends with a leak check at the flex connector and the valve. Stacked pairs in Greenacres closets add drum-bearing work to the mix.
When a dryer trips its breaker, plenty of homeowners phone an electrician first. In the Valley that symptom comes from two very different faults, a shorted element and a worn 30-amp receptacle, and from the panel they look identical. One technician tests the dryer and the receptacle on a single visit, so you know which one failed. We repair Whirlpool, Maytag, Samsung, LG, GE, Kenmore, Electrolux, Frigidaire, Bosch and Speed Queen, and a van is somewhere in the Valley most days. On the long-serving machines in the older ranches, the drum glides wear along with the belt, and we replace them while the drum is already out rather than leaving them for a second visit.
Valley dryer repair starting prices
Two jobs account for most Valley dryer tickets. A new heating element starts at $175, and a thermal fuse or thermostat at $125. When the vent is the only problem, cleaning it is priced as its own small job, starting from $100. Those starting prices come from work across the Spokane area and are a guide, not a quote. Your actual figure is written after the diagnostic with the $99 counted inside it, and turning the repair down leaves the $99 as the whole bill. If a part has to come from a supplier, the written number holds and the return visit carries no trip fee.
| Repair | Price |
|---|---|
| Electric dryer heating element | from $175 |
| Dryer thermal fuse or thermostat | from $125 |
| Dryer vent cleaning | from $100 |
| Gas dryer igniter or valve coils | from $150 |
| Dryer belt, rollers and idler | from $175 |
| Dryer control board | from $250 |
Starting prices in the Spokane area for 2026, part and work included. Not a quote: your exact price is in the written estimate after the $99 diagnostic.
Questions we hear
Can you fix a no-heat dryer in Spokane Valley the same day?
Often. Elements, thermal fuses, igniters and valve coils are stocked on the van, and a van is usually somewhere in the Valley already, so a morning call frequently lands a window that afternoon or early the next day. If your model needs an unusual part, we order it and come back with no second trip fee.
Is a two-cycle dryer worth fixing?
Almost always. Slow drying usually traces to a restricted vent or a tired element, and both are routine repairs. If the machine is old enough that the money would serve you better elsewhere, the technician tells you during the diagnostic, and the $99 is all you pay.
Do gas dryers in Greenacres and Veradale cost more to repair?
No. Fuel type does not change the diagnostic, the quote format or the warranty. Gas jobs add a leak check at the connector and the valve every time, and the igniters and coils that fail on gas units are carried on the van just like electric elements.
My dryer trips the breaker. Is the dryer the problem?
Not always. The same technician meters the dryer's element and motor and the receptacle feeding it, because a shorted element and a worn 30-amp receptacle trip a breaker the same way. You find out which one failed before anything is replaced.
Can you just clean the vent?
Yes. If the dryer tests fine and the run is the only problem, cleaning the vent is quoted as its own small job. On ranch crawlspace runs and two-story roof runs alike, we clear from the drum outlet to the hood and measure airflow afterward so you can see the change.
Call, text or book
Reserve a Valley dryer visit on the website and up to $22 comes off the repair; a call or text works just as well if you would rather talk it through. Either way, your $99 diagnostic is folded into the number you sign, and no distance surcharge applies.
Book a visit
Tell us what is going on
We call or text back to confirm a time window, usually the same day.
- $99 diagnostic Counted inside the written repair price you approve. Say no to the repair and it is the whole bill.
- Up to $50 off An HVAC repair booked online. Appliance repairs booked online: up to $22 off. Never taken off the diagnostic.
- Up to $500 off A full-system install booked through our site-visit form, first-year tune-up included. The site visit costs nothing.
Prefer to text? Send a photo of the model tag to (509) 370-5361.